Compliance
Unpopulated PCBs
lo-tech.co.uk un-populated PCBs are intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, or EVALUATION PURPOSES ONLY and are not considered by Peacon Ltd to be finished end-products fit for general consumer use. Persons handling the product(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards.
These products do not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives, unless otherwise stated.
Should an un-populated PCB not meet the specifications provided on this site, the board may be returned within 30 days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies Peacon Ltd from all claims arising from the handling or use of the goods. Due to the open construction of the products once assembled, it is the user’s responsibility to take any and all appropriate precautions with regard to electrostatic discharge.
EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
Lo-tech GPIO Interface Board rev.2 (Assembled Version)
The Lo-tech GPIO Interface Board rev.2 (Assembled Version) complies with the relevant provisions of the RoHS Directive for the European Union. In common with all Electrical and Electronic Equipment (EEE) the device should not be disposed of as household waste (see WEEE). Alternative arrangements may apply in other jurisdictions.
Electromagnetic Compatibility (EMC)
Note: EMC Performance of the Raspberry Pi is influenced greatly by the attached power supply and casing design. A properly grounded enclosure and a compliant power supply must be used with this product in order to meet FCC emission limits.
- European Compliance Statement
- This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to the European Standard.
- Federal Communications Commission (FCC) Emissions Compliance Statement
- Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the product documentation, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
Peacon Ltd is not responsible for any radio or television interference caused by operating device under conditions other than recommended or by unauthorised changes or modifications to this equipment. Unauthorised changes or modifications could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Responsible Party: Peacon Ltd
Lo-tech Raspberry Pi VGA Interface (Assembled Version)
The Lo-tech RPi VGA Adapter (Assembled Version) complies with the relevant provisions of the RoHS Directive for the European Union. In common with all Electrical and Electronic Equipment (EEE) the device should not be disposed of as household waste (see WEEE). Alternative arrangements may apply in other jurisdictions.
Electromagnetic Compatibility (EMC)
Note: EMC Performance of the Raspberry Pi is influenced greatly by the attached power supply and casing design. A compliant power supply must be used with this product in order to meet FCC emission limits.
- European Compliance Statement
- This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to the European Standard.
- Federal Communications Commission (FCC) Emissions Compliance Statement
- Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the product documentation, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
Peacon Ltd is not responsible for any radio or television interference caused by operating device under conditions other than recommended or by unauthorised changes or modifications to this equipment. Unauthorised changes or modifications could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Responsible Party: Peacon Ltd