Lo-tech 8-bit IDE Adapter

From Lo-tech Wiki
Jump to navigation Jump to search

Note: This board has been superseded by the Lo-tech 8-bit IDE Adapter rev.2.

Lo-tech 8-bit IDE Adapter

The Lo-tech 8-bit IDE Adapter is a bootable storage adapter for IBM PC, PC/XT, PC/AT and compatible hardware - essentially any PC with an ISA slot. The card enables the use of standard IDE (ATA) and SATA hard drives (via a SATA to IDE bridge).

The BIOS ROM on the card enables the host PC to boot from storage presented by the adapter, which appears in DOS as an ordinary fixed disk (i.e. drive C, D, etc). No DOS drivers are needed.

The PCB itself is a through-hole, 8-bit ISA adapter providing a 40-pin IDE header suitable for connection to one or two disk devices. The design goals were:

  • Bootable storage adapter for 8-bit PCs using standard hard disks
  • Ease of home assembly, by use of only through-hole components for basic operation
  • IBM Personal Computer XT System Board Slot 8 compatibility (with optional SMD components mounted on rear of PCB)
  • 5V supply to IDE header key-pin, for cable-less operation of Disk-On-Module devices and SATA to IDE Adapters that support this power option
  • Equal read and write speed

The board uses the same ATA register mapping as other Lo-tech XT-CF boards and uses the XT-IDE Universal BIOS adapter type 'XT-CF (PIO with BIU Offload)' (XT-CF BIU). Note that currently, a specific BIOS build is used, pending integration of changes back into the XTIDE Universal BIOS source. The BIOS is provided through an in-system re-programmable 32KB flash-based ROM operating at either C800h or D800h (user selectable). Since the BIOS is only 8KB, 24KB is available for other purposes, and is byte-programmable - the board can therefore function as a universal ROM board.

This kit is available now in the Lo-tech PCB Store.

If only CompactFlash or SD Card storage is required, the Lo-tech ISA CompactFlash Adapter offers equivalent functionality with a lower component count.

Jumper Settings & System Resources

  • ROM BIOS - 32KB at:
    • JP1 Closed, JP2 Closed: C800h
    • JP1 Closed, JP2 Open: D800h
  • ROM BIOS can be disabled (for example, if a bad flash causes system hang at startup) by opening JP1.
  • IO Ports - 300 to 31Fh (fixed)

ROM BIOS & BIOS Flashing

  • The board is powered by the XT-IDE Universal BIOS and features a 32KB in-system re-programmable flash chip.
  • Pre-configured BIOS files based on XTIDE Universal BIOS R567. Note that this BIOS has been modified for the 8-bit IDE Adapter by disabling the 8-bit media set function (AH9h_Enable8bitModeForDevice8bitAta).
  • The flash chip is programmed with the Lo-tech XT-CF flash utility
  • Select the appropriate ROM image:
    • IDE_XT.BIN for Intel 8088 and 8086 CPUs
    • IDE_XTP.BIN for NEC V20, V30, and Intel 80286 CPUs

Note: The late initialisation module in the XTIDE Universal BIOS should only be included in the BIOS build for systems that require this. The module can cause the BIOS to hang after initialisation on other systems. The BIOS build above excludes this module.

To program the board, make a DOS boot disk (utilities have been tested on MS-DOS 2.11, 3.3 and 6.22) and add the BIOS binary files and the flash utility from the download. Install the Lo-tech 8-bit IDE Adapter in the machine and boot from the floppy, then flash the ROM thus:

A:\>flash ide_xt.bin c800 

Note that should a board containing the IDE_XTP.BIN image be moved to an Intel 8088/8086 PC, the BIOS image will cause the machine to hang during the POST. To resolve this, either re-flash the board with the IDE_XT.BIN image before moving, or disable the ROM during the POST via JP1. JP1 can be closed once the machine has booted, so enabling the ROM for programming (provided there is no other ROM at the address selected with JP2).

Bill of Materials

Part Device Package Qty Farnell Mouser
C1 – C14 0.1uF Ceramic Capacitor C025-030X050 14 2112751 581-SR205E104MAR
C15, C16 22uF Electrolytic Capacitor E2-5 2 9451064 647-UVR1C220MDD
HD1 T821140A1S100CEU 2x20 Pin Header, 2.54mm spacing 1 2215314 517-30340-6002
IC1, IC3 74HCT688N DIL20 2 382504 771-74HCT688N
IC2 SST39SF010ADIP32 DIL32 1 1896595 804-39SF010A7CPHE
IC4 74HCT139N DIL16 1 382036 595-SN74HCT139N
IC5, IC8, IC9 74HCT245N DIL20 3 9591931 595-SN74HCT245N
IC6, IC7 74HCT573N DIL20 2 9592091 595-SN74HCT573N
IC10, IC12 74HCT32N DIL14 2 9591982 595-SN74HCT32N
IC11 74HCT02N DIL14 1 1740019 595-SN74HCT02N
IC13 74HCT04N DIL14 1 9591770 595-SN74HCT04N
IC14 74LS04N DIL14 1 1106072 595-SN74LS04N
JP1, JP2, LED PINHD-1X2 1X02 3 1593411 855-M20-9990246
R1 – R5 RESISTOR, 10K, 125MW 0204/7 5 9342419 270-10K-RC
R6 RESISTOR, 0.125W 1% 270R 0204/7 1 2329504 270-270-RC
R7, R8 RESISTOR, 10K, 125MW 0805 2 1612522 71-CRCW0805J-10K-E3
U1 74LS33D SOIC-14 1 1752958 595-SN74LS33D
C17 CAPACITOR, 0.1UF, 50V 0805 1 1612208 VJ0805V104MXBPW1BC
DIP-14 Socket - - 5 1101346 571-1-390261-3
DIP-16 Socket - - 1 1101347 571-1-390261-4
DIP-20 Socket - - 7 1101349 571-1-390261-6
DIP-32 Socket - - 1 1654375 571-1-2199300-2
2.54mm 2-pin Jumper - - 2 1654800 -

Design

Use of this design is provided subject to the lo-tech.co.uk Terms and Conditions.

Errata

IC11 pin 6 is connected to /PORT0 signal (generated by IC4 pin 12) but should instead be NOT /PORT1.

IC11 pin 6 should be bent out or clipped, such as it does not make contact with the DIP socket, and jumpered to pin 11. See blog entry for more details.

ISA Bracket

Uses Lo-tech ISA Slot Bracket Type 3.

See Also